Product Overview

Description

The KMC KM725 Terra is a cast aluminum wheel in a Satin Black finish, offered here in 16, 17, 18 and 20 in diameters. Priced per wheel, or as a set of 4.

Key features

  • Construction: Cast Aluminum
  • Finish: Satin Black
  • Diameters: 16, 17, 18 and 20 in; widths: 8, 8.5 and 9 in
  • Lug counts: 5 and 6
  • Load rating: 2,500 lbs per wheel

Specifications

Brand KMC
Style KM725 Terra
Finish Satin Black
Construction Cast Aluminum
Diameter 16, 17, 18 and 20 in
Width 8, 8.5 and 9 in
Bolt patterns 5x127, 5x150, 6x120, 6x135, 6x139.7
Lug count 5 and 6
Offset -38 to +25 mm
Centerbore 66.9, 71.5, 87.1, 95.1, 106.1, 110.5 mm
Load rating 2,500 lbs
Beadlock No
Wheel weight 21.4–35.4 lbs
Set of 4 Four wheels

Sizes in this listing

Size Bolt pattern Bolt pattern (in) Offset Backspacing Centerbore Load rating Weight Part number Set of 4
16x8 6x139.7 6x5.5 +0 mm 4.5 in 106.1 mm 2,500 lbs 21.4 lbs KM725MX16806800 4 × KM725MX16806800
17x8.5 6x139.7 6x5.5 -10 mm 4.36 in 106.1 mm 2,500 lbs 26.4 lbs KM725MX17856810N 4 × KM725MX17856810N
17x8.5 5x127 5x5 +0 mm 4.75 in 71.5 mm 2,500 lbs 26.4 lbs KM725MX17855000 4 × KM725MX17855000
17x8.5 6x120 – +0 mm 4.75 in 66.9 mm 2,500 lbs 26.4 lbs KM725MX17857700 4 × KM725MX17857700
17x8.5 6x135 – +0 mm 4.75 in 87.1 mm 2,500 lbs 25.8 lbs KM725MX17856300 4 × KM725MX17856300
17x8.5 6x139.7 6x5.5 +0 mm 4.75 in 106.1 mm 2,500 lbs 25.8 lbs KM725MX17856800 4 × KM725MX17856800
17x8.5 5x150 – +25 mm 5.73 in 110.5 mm 2,500 lbs 27.8 lbs KM72078558725 4 × KM72078558725
17x8.5 6x139.7 6x5.5 +25 mm 5.73 in 95.1 mm 2,500 lbs 27.8 lbs KM72078562725 4 × KM72078562725
17x9 5x127 5x5 -38 mm 3.5 in 71.5 mm 2,500 lbs 26.9 lbs KM725MX17905038N 4 × KM725MX17905038N
17x9 6x139.7 6x5.5 -38 mm 3.5 in 106.1 mm 2,500 lbs 26.4 lbs KM725MX17906838N 4 × KM725MX17906838N
18x8.5 5x127 5x5 -10 mm 4.36 in 71.5 mm 2,500 lbs 29.3 lbs KM725MX18855010N 4 × KM725MX18855010N
18x8.5 6x139.7 6x5.5 -10 mm 4.36 in 106.1 mm 2,500 lbs 28.8 lbs KM725MX18856810N 4 × KM725MX18856810N
18x8.5 6x135 – +0 mm 4.75 in 87.1 mm 2,500 lbs 28.4 lbs KM725MX18856300 4 × KM725MX18856300
18x8.5 6x139.7 6x5.5 +0 mm 4.75 in 106.1 mm 2,500 lbs 27.9 lbs KM725MX18856800 4 × KM725MX18856800
20x9 5x127 5x5 -12 mm 4.53 in 71.5 mm 2,500 lbs 35.4 lbs KM725MX20905012N 4 × KM725MX20905012N
20x9 6x139.7 6x5.5 -12 mm 4.53 in 106.1 mm 2,500 lbs 34.5 lbs KM725MX20906812N 4 × KM725MX20906812N
20x9 6x135 – +0 mm 5 in 87.1 mm 2,500 lbs 34.1 lbs KM725MX20906300 4 × KM725MX20906300
20x9 6x139.7 6x5.5 +0 mm 5 in 106.1 mm 2,500 lbs 33.9 lbs KM725MX20906800 4 × KM725MX20906800

Confirm bolt pattern, offset and load rating for your vehicle before ordering.

Free shipping on orders $150+

FAQs

Please read our FAQs page to find out more.

RMS vs. MAX power — which number do I actually care about?

RMS is what your gear handles continuously; MAX is the short burst it can survive without complaint. Match your amplifier's RMS output to your speakers' RMS rating — sizing off the MAX number is how magic smoke gets released.

What does the IP65 rating on DS18 marine gear actually mean?

It's dust-tight and rated against low-pressure water jets from any direction — built for spray, rain, and the occasional wave over the bow, not for full submersion. If something's going somewhere it could sit underwater, that's a different conversation entirely.

How do I match an amplifier to my speakers without guessing?

Add up the RMS rating of everything the amp will power, and pick an amp whose RMS output (at your speakers' impedance — usually 4-ohm) lands close to that total. Undersized is thin sound; wildly oversized is a fast way to blow a voice coil.

Can I mix marine-grade gear into a standard car audio setup, or the reverse?

You can run marine-grade gear in a car — it's just over-built for that environment, no downside besides cost. Running non-weatherproof car audio gear in an open UTV or boat is the direction that causes problems.

What gauge wiring kit do I need?

It scales with your amp's power draw and the length of the run — DS18's OFC kits come in 4-gauge and 8-gauge for a reason. Undersized wiring on a high-draw system is a voltage-drop and heat problem waiting to happen; when in doubt, size up.

Didn’t find your answer?

Don't hestitate to contact us