Product Overview

Description

The KMC KM238 VI Beadlock is a cast aluminum wheel in a Machined finish, offered here in 17 and 20 in diameters. Priced per wheel, or as a set of 4.

Key features

  • Construction: Cast Aluminum
  • Finish: Machined
  • Beadlock wheel
  • Diameters: 17 and 20 in; widths: 9 and 10 in
  • Lug counts: 5, 6 and 8
  • Load rating: 4,000 lbs per wheel

Specifications

Brand KMC
Style KM238 VI Beadlock
Finish Machined
Construction Cast Aluminum
Diameter 17 and 20 in
Width 9 and 10 in
Bolt patterns 5x127, 5x150, 6x135, 6x139.7, 8x165.1, 8x170
Lug count 5, 6 and 8
Offset -48 to +1 mm
Centerbore 71.5, 87.1, 108, 110.1, 125.1 mm
Load rating 4,000 lbs
Beadlock Yes
Use Off-road use only (manufacturer's statement)
Wheel weight 35–48.2 lbs
Set of 4 Four wheels

Note from KMC: beadlock wheels are sold for off-road use only. Off-road-use-only wheels are illegal on public roads in many states and provinces, as they are intended only for racing and/or off-road vehicles.

Sizes in this listing

Size Bolt pattern Bolt pattern (in) Offset Backspacing Centerbore Load rating Weight Part number Set of 4
17x9 5x127 5x5 -38 mm 3.5 in 71.5 mm 4,000 lbs 38.5 lbs KM238DX17905038N 4 × KM238DX17905038N
17x9 6x135 – -38 mm 3.5 in 87.1 mm 4,000 lbs 38.5 lbs KM238DX17906338N 4 × KM238DX17906338N
17x9 6x139.7 6x5.5 -38 mm 3.5 in 108 mm 4,000 lbs 38.5 lbs KM238DX17906038N 4 × KM238DX17906038N
17x9 8x165.1 8x6.5 -38 mm 3.5 in 125.1 mm 4,000 lbs 38.7 lbs KM238DX17908038N 4 × KM238DX17908038N
17x9 8x170 – -38 mm 3.5 in 125.1 mm 4,000 lbs 38.7 lbs KM238DX17908738N 4 × KM238DX17908738N
17x9 5x127 5x5 -12 mm 4.53 in 71.5 mm 4,000 lbs 36.1 lbs KM238DX17905012N 4 × KM238DX17905012N
17x9 6x139.7 6x5.5 -12 mm 4.53 in 110.1 mm 4,000 lbs 36.4 lbs KM238DX17906012N 4 × KM238DX17906012N
17x9 5x150 – +1 mm 5.04 in 110.1 mm 4,000 lbs 35 lbs KM238DX17905801 4 × KM238DX17905801
17x9 6x135 – +1 mm 5.04 in 87.1 mm 4,000 lbs 35.5 lbs KM238DX17906301 4 × KM238DX17906301
17x9 6x139.7 6x5.5 +1 mm 5.04 in 110.1 mm 4,000 lbs 35 lbs KM238DX17906001 4 × KM238DX17906001
20x10 5x127 5x5 -48 mm 3.61 in 71.5 mm 4,000 lbs 48 lbs KM238DX20105048N 4 × KM238DX20105048N
20x10 6x135 – -48 mm 3.61 in 87.1 mm 4,000 lbs 48 lbs KM238DX20106348N 4 × KM238DX20106348N
20x10 6x139.7 6x5.5 -48 mm 3.61 in 108 mm 4,000 lbs 48 lbs KM238DX20106048N 4 × KM238DX20106048N
20x10 8x165.1 8x6.5 -48 mm 3.61 in 125.1 mm 4,000 lbs 48.2 lbs KM238DX20108048N 4 × KM238DX20108048N
20x10 8x170 – -48 mm 3.61 in 125.1 mm 4,000 lbs 48.2 lbs KM238DX20108748N 4 × KM238DX20108748N

Confirm bolt pattern, offset and load rating for your vehicle before ordering.

Free shipping on orders $150+

FAQs

Please read our FAQs page to find out more.

RMS vs. MAX power — which number do I actually care about?

RMS is what your gear handles continuously; MAX is the short burst it can survive without complaint. Match your amplifier's RMS output to your speakers' RMS rating — sizing off the MAX number is how magic smoke gets released.

What does the IP65 rating on DS18 marine gear actually mean?

It's dust-tight and rated against low-pressure water jets from any direction — built for spray, rain, and the occasional wave over the bow, not for full submersion. If something's going somewhere it could sit underwater, that's a different conversation entirely.

How do I match an amplifier to my speakers without guessing?

Add up the RMS rating of everything the amp will power, and pick an amp whose RMS output (at your speakers' impedance — usually 4-ohm) lands close to that total. Undersized is thin sound; wildly oversized is a fast way to blow a voice coil.

Can I mix marine-grade gear into a standard car audio setup, or the reverse?

You can run marine-grade gear in a car — it's just over-built for that environment, no downside besides cost. Running non-weatherproof car audio gear in an open UTV or boat is the direction that causes problems.

What gauge wiring kit do I need?

It scales with your amp's power draw and the length of the run — DS18's OFC kits come in 4-gauge and 8-gauge for a reason. Undersized wiring on a high-draw system is a voltage-drop and heat problem waiting to happen; when in doubt, size up.

Didn’t find your answer?

Don't hestitate to contact us