Product Overview

Description

The KMC KS235 Grenade Beadlock is a cast aluminum UTV wheel in a Satin Black finish, offered here in 14, 15 and 18 in diameters. Priced per wheel, or as a set of 4.

Key features

  • Construction: Cast Aluminum
  • Finish: Satin Black
  • Beadlock wheel
  • Diameters: 14, 15 and 18 in; widths: 6, 7, 9 and 10 in
  • Lug counts: 4 and 5
  • Load rating: 1,000–1,300 lbs per wheel, depending on size

Specifications

Brand KMC
Style KS235 Grenade Beadlock
Finish Satin Black
Construction Cast Aluminum
Diameter 14, 15 and 18 in
Width 6, 7, 9 and 10 in
Bolt patterns 4x110, 4x137, 4x156, 5x114.3
Lug count 4 and 5
Offset -24 to +38 mm
Centerbore 72.56, 86, 112.1, 115.1, 132 mm
Load rating 1,000–1,300 lbs
Beadlock Yes
Use Off-road use only (manufacturer's statement)
Wheel weight 15.8–32 lbs
Set of 4 Four wheels

Note from KMC: beadlock wheels are sold for off-road use only. Off-road-use-only wheels are illegal on public roads in many states and provinces, as they are intended only for racing and/or off-road vehicles.

Sizes in this listing

Size Bolt pattern Bolt pattern (in) Offset Backspacing Centerbore Load rating Weight Part number Set of 4
14x7 4x137 – +10 mm 4.39 in 112.1 mm 1,000 lbs 17 lbs KS23547048710 4 × KS23547048710
14x7 4x156 – +10 mm 4.39 in 132 mm 1,000 lbs 16.1 lbs KS23547044710 4 × KS23547044710
14x7 4x110 – +38 mm 5.5 in 86 mm 1,000 lbs 17.7 lbs KS23547040738 4 × KS23547040738
14x7 4x137 – +38 mm 5.5 in 112.1 mm 1,000 lbs 17.5 lbs KS23547048738 4 × KS23547048738
14x7 4x156 – +38 mm 5.5 in 132 mm 1,000 lbs – KS23547044738 4 × KS23547044738
14x10 4x156 – +0 mm 5.5 in 132 mm 1,000 lbs 17.6 lbs KS23541044700 4 × KS23541044700
15x6 4x137 – +38 mm 5 in 112.1 mm 1,000 lbs 17.2 lbs KS23556048738 4 × KS23556048738
15x6 4x156 – +38 mm 5 in 132 mm 1,000 lbs – KS23556044738 4 × KS23556044738
15x6 5x114.3 5x4.5 +38 mm 5 in 72.56 mm 1,000 lbs 15.8 lbs KS23556012738 4 × KS23556012738
15x7 4x110 – +10 mm 4.39 in 86 mm 1,300 lbs 16.8 lbs KS23557040710 4 × KS23557040710
15x7 4x137 – +10 mm 4.39 in 112.1 mm 1,300 lbs 16.8 lbs KS23557048710 4 × KS23557048710
15x7 4x156 – +10 mm 4.39 in 115.1 mm 1,300 lbs 16.8 lbs KS23557044710 4 × KS23557044710
15x10 4x137 – +0 mm 5.5 in 112.1 mm 1,000 lbs 20.3 lbs KS23551048700 4 × KS23551048700
15x10 4x156 – +0 mm 5.5 in 132 mm 1,000 lbs 19.7 lbs KS23551044700 4 × KS23551044700
15x10 5x114.3 5x4.5 +0 mm 5.5 in 72.56 mm 1,000 lbs 18.3 lbs KS23551012700 4 × KS23551012700
18x9 4x137 – -24 mm 4.06 in 112.1 mm 1,000 lbs 32 lbs KS23589048724N 4 × KS23589048724N

Confirm bolt pattern, offset and load rating for your vehicle before ordering.

Free shipping on orders $150+

FAQs

Please read our FAQs page to find out more.

RMS vs. MAX power — which number do I actually care about?

RMS is what your gear handles continuously; MAX is the short burst it can survive without complaint. Match your amplifier's RMS output to your speakers' RMS rating — sizing off the MAX number is how magic smoke gets released.

What does the IP65 rating on DS18 marine gear actually mean?

It's dust-tight and rated against low-pressure water jets from any direction — built for spray, rain, and the occasional wave over the bow, not for full submersion. If something's going somewhere it could sit underwater, that's a different conversation entirely.

How do I match an amplifier to my speakers without guessing?

Add up the RMS rating of everything the amp will power, and pick an amp whose RMS output (at your speakers' impedance — usually 4-ohm) lands close to that total. Undersized is thin sound; wildly oversized is a fast way to blow a voice coil.

Can I mix marine-grade gear into a standard car audio setup, or the reverse?

You can run marine-grade gear in a car — it's just over-built for that environment, no downside besides cost. Running non-weatherproof car audio gear in an open UTV or boat is the direction that causes problems.

What gauge wiring kit do I need?

It scales with your amp's power draw and the length of the run — DS18's OFC kits come in 4-gauge and 8-gauge for a reason. Undersized wiring on a high-draw system is a voltage-drop and heat problem waiting to happen; when in doubt, size up.

Didn’t find your answer?

Don't hestitate to contact us