Product Overview

Description

The Black Rhino Abrams is a cast aluminum wheel in a Textured Matte Gunmetal finish, offered here in 17, 18 and 20 in diameters. Priced per wheel, or as a set of 4.

Key features

  • Construction: Cast Aluminum
  • Finish: Textured Matte Gunmetal
  • Diameters: 17, 18 and 20 in; widths: 8.5 and 9.5 in
  • Lug counts: 5, 6 and 8
  • Load rating: 2,250–3,640 lbs per wheel, depending on size

Specifications

Brand Black Rhino
Style Abrams
Finish Textured Matte Gunmetal
Construction Cast Aluminum
Diameter 17, 18 and 20 in
Width 8.5 and 9.5 in
Bolt patterns 5x127, 6x114.3, 6x120, 6x135, 6x139.7, 8x165.1, 8x170, 8x180
Lug count 5, 6 and 8
Offset -18 to +12 mm
Centerbore 67.06, 71.5, 76.1, 87.1, 112.1, 122.4, 125.1 mm
Load rating 2,250–3,640 lbs
Beadlock No
Wheel weight 30.7–43.5 lbs
Set of 4 Four wheels

Sizes in this listing

Size Bolt pattern Bolt pattern (in) Offset Backspacing Centerbore Load rating Weight Part number Set of 4
17x8.5 6x135 – -18 mm 4.04 in 87.1 mm 2,500 lbs 32 lbs 1785ABR-86135G87 4 × 1785ABR-86135G87
17x8.5 6x139.7 6x5.5 -18 mm 4.04 in 112.1 mm 2,500 lbs 41 lbs 1785ABR-86140G12 4 × 1785ABR-86140G12
17x8.5 6x114.3 6x4.5 +0 mm 4.75 in 76.1 mm 2,500 lbs 30.7 lbs 1785ABR006114G76 4 × 1785ABR006114G76
17x8.5 6x139.7 6x5.5 +0 mm 4.75 in 112.1 mm 2,500 lbs 30.7 lbs 1785ABR006140G12 4 × 1785ABR006140G12
17x9.5 5x127 5x5 -18 mm 4.54 in 71.5 mm 2,250 lbs 35.5 lbs 1795ABR-85127G71 4 × 1795ABR-85127G71
17x9.5 8x165.1 8x6.5 -18 mm 4.54 in 122.4 mm 3,640 lbs – 1795ABR-88165G22 4 × 1795ABR-88165G22
17x9.5 8x170 – -18 mm 4.54 in 125.1 mm 3,640 lbs – 1795ABR-88170G25 4 × 1795ABR-88170G25
17x9.5 8x180 – -18 mm 4.54 in 125.1 mm 3,640 lbs – 1795ABR-88180G25 4 × 1795ABR-88180G25
18x9.5 5x127 5x5 -18 mm 4.54 in 71.5 mm 2,250 lbs – 1895ABR-85127G71 4 × 1895ABR-85127G71
18x9.5 8x165.1 8x6.5 -18 mm 4.54 in 122.4 mm 3,640 lbs 36 lbs 1895ABR-88165G22 4 × 1895ABR-88165G22
18x9.5 8x180 – -18 mm 4.54 in 125.1 mm 3,640 lbs 36 lbs 1895ABR-88180G25 4 × 1895ABR-88180G25
18x9.5 6x139.7 6x5.5 +12 mm 5.72 in 112.1 mm 2,500 lbs 32.6 lbs 1895ABR126140G12 4 × 1895ABR126140G12
20x9.5 5x127 5x5 -18 mm 4.54 in 71.5 mm 2,250 lbs 43 lbs 2095ABR-85127G71 4 × 2095ABR-85127G71
20x9.5 8x165.1 8x6.5 -18 mm 4.54 in 122.4 mm 3,640 lbs 43.5 lbs 2095ABR-88165G22 4 × 2095ABR-88165G22
20x9.5 8x170 – -18 mm 4.54 in 125.1 mm 3,640 lbs 43.5 lbs 2095ABR-88170G25 4 × 2095ABR-88170G25
20x9.5 6x139.7 6x5.5 +2 mm 5.33 in 112.1 mm 2,500 lbs 39.6 lbs 2095ABR026140G12 4 × 2095ABR026140G12
20x9.5 6x120 – +12 mm 5.72 in 67.06 mm 2,500 lbs 39.1 lbs 2095ABR126120G67 4 × 2095ABR126120G67

Confirm bolt pattern, offset and load rating for your vehicle before ordering.

Free shipping on orders $150+

FAQs

Please read our FAQs page to find out more.

RMS vs. MAX power — which number do I actually care about?

RMS is what your gear handles continuously; MAX is the short burst it can survive without complaint. Match your amplifier's RMS output to your speakers' RMS rating — sizing off the MAX number is how magic smoke gets released.

What does the IP65 rating on DS18 marine gear actually mean?

It's dust-tight and rated against low-pressure water jets from any direction — built for spray, rain, and the occasional wave over the bow, not for full submersion. If something's going somewhere it could sit underwater, that's a different conversation entirely.

How do I match an amplifier to my speakers without guessing?

Add up the RMS rating of everything the amp will power, and pick an amp whose RMS output (at your speakers' impedance — usually 4-ohm) lands close to that total. Undersized is thin sound; wildly oversized is a fast way to blow a voice coil.

Can I mix marine-grade gear into a standard car audio setup, or the reverse?

You can run marine-grade gear in a car — it's just over-built for that environment, no downside besides cost. Running non-weatherproof car audio gear in an open UTV or boat is the direction that causes problems.

What gauge wiring kit do I need?

It scales with your amp's power draw and the length of the run — DS18's OFC kits come in 4-gauge and 8-gauge for a reason. Undersized wiring on a high-draw system is a voltage-drop and heat problem waiting to happen; when in doubt, size up.

Didn’t find your answer?

Don't hestitate to contact us