Product Overview

Description

The American Force 75 Burnout SS is a monoblock forged wheel in a Polished finish, offered here in 20, 22, 24 and 26 in diameters. Priced per wheel. Made to order. Lead time is confirmed after you order.

Key features

  • Construction: Monoblock Forged
  • Finish: Polished
  • Diameters: 20, 22, 24 and 26 in; widths: 10, 11, 12, 14 and 16 in
  • Lug counts: 5, 6 and 8
  • Load rating: 2,500–3,500 lbs per wheel, depending on size

Specifications

Brand American Force
Style 75 Burnout SS
Finish Polished
Construction Monoblock Forged
Diameter 20, 22, 24 and 26 in
Width 10, 11, 12, 14 and 16 in
Bolt patterns 5x127, 5x139.7, 5x150, 6x135, 6x139.7, 8x165.1, 8x170
Lug count 5, 6 and 8
Offset -101 to +0 mm
Centerbore 71.5, 77.8, 78.1, 87, 108, 110, 122, 125 mm
Load rating 2,500–3,500 lbs
Beadlock No

Sizes in this listing

Size Bolt pattern Bolt pattern (in) Offset Backspacing Centerbore Load rating Part number
20x10 6x135 – -25 mm 4.52 in 87 mm 3,500 lbs AFTD75W87-1-21
20x10 6x139.7 6x5.5 -25 mm 4.52 in 78.1 mm 3,500 lbs AFTD75R78-1-21
20x12 8x165.1 8x6.5 -40 mm 4.93 in 122 mm 3,500 lbs AFTE75D22-1-21
22x11 8x170 – +0 mm 6 in 125 mm 3,500 lbs AFTH75F25-1-21
22x12 5x139.7 5x5.5 -40 mm 4.93 in 77.8 mm 3,500 lbs AFTJ75N77-1-21
22x12 5x150 – -40 mm 4.93 in 110 mm 3,500 lbs AFTJ75T10-1-21
22x12 6x135 – -40 mm 4.93 in Not stated by supplier 2,500 lbs AFTJ75W87-1-10
22x12 8x165.1 8x6.5 -40 mm 4.93 in 122 mm 3,500 lbs AFTJ75D22-1-21
22x14 6x139.7 6x5.5 -72 mm 4.67 in Not stated by supplier 2,500 lbs AFTK75R06-1-20
22x14 8x165.1 8x6.5 -73 mm 4.63 in 125 mm 3,500 lbs AFTK75F25-1-21
24x12 5x127 5x5 -40 mm 4.93 in 71.5 mm 3,500 lbs AFTN75S71-1-21
24x12 6x139.7 6x5.5 -40 mm 4.93 in 108 mm 3,500 lbs AFTN75R08-1-21
24x14 8x170 – -73 mm 4.63 in 125 mm 3,500 lbs AFTP75F25-1-21
26x16 6x139.7 6x5.5 -101 mm 4.52 in Not stated by supplier 2,500 lbs AFTS75R06-1-20

Confirm bolt pattern, offset and load rating for your vehicle before ordering.

Free shipping on orders $150+

FAQs

Please read our FAQs page to find out more.

RMS vs. MAX power — which number do I actually care about?

RMS is what your gear handles continuously; MAX is the short burst it can survive without complaint. Match your amplifier's RMS output to your speakers' RMS rating — sizing off the MAX number is how magic smoke gets released.

What does the IP65 rating on DS18 marine gear actually mean?

It's dust-tight and rated against low-pressure water jets from any direction — built for spray, rain, and the occasional wave over the bow, not for full submersion. If something's going somewhere it could sit underwater, that's a different conversation entirely.

How do I match an amplifier to my speakers without guessing?

Add up the RMS rating of everything the amp will power, and pick an amp whose RMS output (at your speakers' impedance — usually 4-ohm) lands close to that total. Undersized is thin sound; wildly oversized is a fast way to blow a voice coil.

Can I mix marine-grade gear into a standard car audio setup, or the reverse?

You can run marine-grade gear in a car — it's just over-built for that environment, no downside besides cost. Running non-weatherproof car audio gear in an open UTV or boat is the direction that causes problems.

What gauge wiring kit do I need?

It scales with your amp's power draw and the length of the run — DS18's OFC kits come in 4-gauge and 8-gauge for a reason. Undersized wiring on a high-draw system is a voltage-drop and heat problem waiting to happen; when in doubt, size up.

Didn’t find your answer?

Don't hestitate to contact us